【vbox】10g rac之cluster安装中运行2号节点root.sh时vipca错误处理实录（红色是教训纪录）
cluster安装到最后环节出现
运行完
在rac1 上执行：/opt/ora10g/oraInventory/orainstRoot.sh
在rac2 上执行：/opt/ora10g/oraInventory/orainstRoot.sh
在rac1 上执行：/opt/ora10g/product/10.2.0/crs_1/root.sh
都没问题
看其他经验指导，rac2上的/opt/ora10g/product/10.2.0/crs_1/root.sh会报错
提前修改一些文件：
每个节点（有一个文档提到全改）
先修改vipca 文件,
[[email protected] opt]# vi /opt/ora10g/product/10.2.0/crs_1/bin/vipca
找到如下内容：
if [ "$arch" = "i686" -o "$arch" = "ia64" ]
then
LD_ASSUME_KERNEL=2.4.19
export LD_ASSUME_KERNEL
fi
#End workaround
在fi 后新添加一行：
unset LD_ASSUME_KERNEL
再修改srvctl 文件
[[email protected] opt]# vi /opt/ora10g/product/10.2.0/crs_1/bin/srvctl
找到如下内容：
LD_ASSUME_KERNEL=2.4.19
export LD_ASSUME_KERNEL
同样在其后新增加一行：
unset LD_ASSUME_KERNEL
然后任意节点
我在2号节点[[email protected] ~]
/opt/oracle/otk/home/oracle/product/10.2.0/crs/bin/oifcfg setif -global eth0/192.168.100.0:public
/opt/oracle/otk/home/oracle/product/10.2.0/crs/bin/oifcfg setif -global eth1/10.10.17.0:cluster_interconnect
/opt/oracle/otk/home/oracle/product/10.2.0/crs/bin/oifcfg getif
最后在rac2 上执行：/opt/ora10g/product/10.2.0/crs_1/root.sh
运行完报错
然后任意节点
[[email protected] cfgtoollogs]# export DISPLAY=192.168.100.1:0.0
[[email protected] cfgtoollogs]# xhost+
[[email protected] cfgtoollogs]# export LANG=c
[[email protected] cfgtoollogs]# /opt/oracle/otk/home/oracle/product/10.2.0/crs/bin/vipca
成功配置完毕
然后回到一号节点orale运行的安装界面上点击ok
（我在提示rac2上运行/opt/ora10g/product/10.2.0/crs_1/root.sh时，没有运行vipca之前，就retry了几次，没过去就给强制关闭了，然后报了个The "/opt/oracle/otk/home/oracle/product/10.2.0/crs/cfgtoollogs/configToolFailedCommands" script contains all commands that failed, were skipped or were cancelled. This file may be used to run these configuration assistants outside of OUI. Note that you may have to update this script with passwords (if any) before executing the same的错误，
我找到日志/opt/oracle/otk/home/oraInventory/logs里发现可以再次运行/opt/oracle/otk/home/oracle/product/10.2.0/crs/oui/bin/ouica.sh
我就在关闭后的rac1下的oracle用户下运行
-bash-3.2$ /opt/oracle/otk/home/oracle/product/10.2.0/crs/oui/bin/ouica.sh
Configuration directory is set to /opt/oracle/otk/home/oracle/product/10.2.0/crs/cfgtoollogs. All xml files under the directory will be processed
-bash-3.2$ /opt/oracle/otk/home/oracle/product/10.2.0/crs/cfgtoollogs
-bash: /opt/oracle/otk/home/oracle/product/10.2.0/crs/cfgtoollogs: is a directory
-bash-3.2$ cd /opt/oracle/otk/home/oracle/product/10.2.0/crs/cfgtoollogs
-bash-3.2$ ls
cfgfw configToolAllCommands configToolFailedCommands oui vipca
-bash-3.2$ ./configToolAllCommands
然后出现了Checking existence of VIP node application (required)
Check failed.
Check failed on nodes:
rac2,rac1
然后我才回到rac2 root下运行vipca，配置成功后，再次运行 ./configToolAllCommands
Checking existence of VIP node application (required)
Check passed.
Post-check for cluster services setup was successful.
）
随后各个节点均显示crs正常
-bash-3.2$ /opt/oracle/otk/home/oracle/product/10.2.0/crs/bin/crs_stat -t
Name Type Target State Host
------------------------------------------------------------
ora.rac1.gsd application ONLINE ONLINE rac1
ora.rac1.ons application ONLINE ONLINE rac1
ora.rac1.vip application ONLINE ONLINE rac1
ora.rac2.gsd application ONLINE ONLINE rac2
ora.rac2.ons application ONLINE ONLINE rac2
ora.rac2.vip application ONLINE ONLINE rac2